Keyboard Layout v Fluke B/1 96B-C/B-C Service Manual List of Figures For the mA. current D pin 3 is connected to pin 1, and pin 13 is. Manual de Servicio Fluke b – Ebook download as PDF File .pdf), Text File . txt) or trigger level mV) or (R the switches in D are all open. F HP Deskjet F HP Deskjet D HP Deskjet D HP Deskjet D . would work while others would not, and maybe it’s some strange fluke.

Author: Shakalkis Dairisar
Country: Togo
Language: English (Spanish)
Genre: Politics
Published (Last): 26 December 2006
Pages: 21
PDF File Size: 3.6 Mb
ePub File Size: 15.37 Mb
ISBN: 211-8-27676-247-2
Downloads: 35725
Price: Free* [*Free Regsitration Required]
Uploader: Faezilkree

To change the strap position open the test tool see Section 6. Verify that the backlight wires are twisted to minimize interference voltages.

Full text of “FLUKE B, B, C, B,C Service”

Connect the test tool to the A as for the previous test see Figure 8. Specified non-tolerance numerical values indicate those that could be nominally expected from the mean of a range of identical ScopeMeter test tools. If flkke error persists the test tool is detecti ve. The pixel pitch is 0.

Select the following test tool setup: An additional phototransistor is used for feed back of a copy of the non- floating LF signal. Do the Contrast Calibration Adjustment, section 5. Type WW 1 ,2, and press [Enter] The test tool must return acknowledge 0 zero Type EX 12H44 0H and press [Enter] The test tool will return one of the following acknowledges: Amazon Giveaway allows you to run promotional giveaways in order to create buzz, reward your audience, flukke attract new followers and customers.

  LIBRO NO LE LLAMES MAS RHONDA FINDLING PDF

After the last data bit has been shifted into the register, the clock signal CLK H pin 7 is kept low. After a number of characters the test tool mask software will respond with an acknowledge 0 zero.

Full text of “FLUKE “

Check the supply voltages on: Wait until the display shows End Precal: Continue flike the test points, 6. It is recommended to make a copy of.

Connect the test tool to the 5 5 00 A as shown in Figure It is derived from reference diode V41 14, as shown in Figure You must continue with the Final Calibration! Reattach the LCD flex cable, secure that cable in the connector with the connector latch. Press iBlEl to continue with d5160 dc calibration.

Examine the rising edge of the dluke marker pulse at the height of the trigger level indicator top. Proceed as follows to test the Peak measurement accuracy: If wrong, continue at step 3. Press dHii to select first calibration adjustment step in Table The samples are stored in an internal analog memory array, and can be read out at a lower speed.

Install the bottom case with the strap holders and strap, and fasten the 2 screws item Introduction This section provides the required disassembling procedures. Press to select the first fluks step in Table The test tool has a normal calibration cycle of one year.

  CATALOGO VIMAR IDEA PDF

HP C9352AE (22) Multi Colour Cartridge for Inkjet Printer

If a A is not available, you can substitute another calibrator as long as it meets the minimum test requirements. Press tllfiil to start the calibration. When, measuring in the input circuits of a the disassembled test tool, the backlight control voltage can cause noise on the measured signals.

The instruction More information.

Technical Details

Power the test tool via the power adapter input using the BC power adapter. This will start up the mask software. Note 2 The Scope channel A and B input attenuator top shieldings are provided with a plate spring. This number is printed on d11560 sticker located on the metal shielding plate around the flat cable connectors.

When you are finished, set the A to d11560 zero Volt, and to Standby. Select the Calibration Mode, section 5. Check the LF path: