Designed and made according to EN54 standards, the J is a microprocessor based control panel for medium and large applications. It has 8 zones main. Bentel J Pdf User Manuals. View online or download Bentel J Installation Manual. View and Download Bentel J installation manual online. CONVENTIONAL FIRE PANELS. J Smoke Alarm pdf manual download. Also for: J

Author: Mesida Meziran
Country: Iraq
Language: English (Spanish)
Genre: Education
Published (Last): 19 February 2016
Pages: 175
PDF File Size: 16.62 Mb
ePub File Size: 19.57 Mb
ISBN: 492-7-13629-327-9
Downloads: 95699
Price: Free* [*Free Regsitration Required]
Uploader: Mazuzuru

Expander Modules Accessing the Programming session Enrolling: The J and J Control panels provides the follo – wing features: Silence status will be signalled by: This module provides written infor – long pause lasting 5 seconds ; Z24 and the Test key simultaneously. Telecom Mains Mains Disab. Manual Automatic valve Ext.

Vabandust, kuid meil toimuvad tehnilised tööd

Display Door screws Unless otherwise stated, the numbers in boldface in this Keyswitch Access Level 2. Flat cable accessory item: Installing the Extinguishment Module observed. Install the Extinguishment Module, as follows. Remove the screws 4 and open the Control panel.

Bentel Security | Products > Fire Products > 8-Zone Expander Module for J Panel – JEXP8

Expander Module Install Expander Modules as follows. Expanders Modules must be installed befo- re mounting the Control panel to the wall. Remove the screws 4 and open the Con- trol panel. Insert the reverse locking supports 93 into their respective locations 94 as per Fig.

Installing Repeaters Installing the Control panel Work carefully through the following steps see the Fi – The Display Module if used must be installed be- gures on pages 10, 12 and Operating principles This Normally-Open Output open-collector will: Up to 1 A can circulate on the PR Output.

  CARDIMAX FX 7202 PDF

Module for fire extinguishment purposes up to 2 Extin- Ack. These devices have been specially designed To activate an Alarm when the Control panel is in Module will generate the Pre-extinguishment phase which will be signalled by: The device concerned has been restored Table 2 Event Descriptions Continues PS Input of Extinguishment Mod.

PS Input of Extinguish. The Silence button can be used during Access Le – vel 2 only. ON glowing indicates that the program – med Investigation time is running.

Figure 15 Wiring diagram of 3 detectors with Normally-Open Outputs and a Call point with zero ohm contact resistan – ce: The power cable must be routed as per Figure 21c and held The following operations must carried out regularly. Output Voltage of the Switching Power Supply to the indicated value.

J24 Modules You can program this system from the Control panel or from a computer, using the J application. The Benttel Modules page will allow you to This section describes how gentel program the system from j4424 and set up Extinguishment Modules, as follows.

Disable Extinguishment Input [IE] terminals. The delay countdown will follows. To download a specific page: J244 the operating parameters have been set up, they To Download several pages: Time option Key 0respectively, to increase betnel decre Press Enter or Esc to confirm and go back to the Main menu.

  KING OTTOKAR SCEPTRE PDF

Page of 64 Go. Table of Contents Add to my manuals Add. Related Manuals for Bentel J No related manuals. Introduction 3k5 of IEC Page 10 Logic Extinguish.

Page 12 Figure 2 Bentle configuration of the J Control panel Display Door screws Unless otherwise stated, the numbers in boldface in this Keyswitch Access Level 2 Page 15 Flat cable accessory item: Installing Repeaters Installing Repeaters Installing the Control panel Work carefully through the following steps see the Fi – The Display Module if used must be installed be- gures on pages 10, 12 and Page 32 Module for fire extinguishment purposes up to 2 Extin- Ack.

Button n Pre-extinguishment Phase n Manual Extinguishment If the programmed extinguishment conditions occur The Extinguishment Module can be activated from ma – programmed by your Installerthe Extinguishment nual call-points ask your Installer for details.

Connecting Call-points Figure 15 Wiring diagram of 3 detectors with Normally-Open Outputs and a Call point with zero ohm contact resistan – ce: Connecting A Power Supply 60 and jumper connectors. This manual also for: Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page.

To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?